[2017 Latest Cisco Questions] High Quality 300-135 Dumps PDF Practice Files, Latest Cisco 300-135 Dumps Youtube

2017 latest Cisco CCNP Routing and Switching 300-135 dumps exam questions and answers free try. High quality Cisco CCNP Routing and Switching 300-135 dumps pdf practice files and study guides update from lead4pass. https://www.lead4pass.com/300-135.html dumps exam training mateials. Latest Cisco CCNP Routing and Switching 300-135 dumps pdf and vce training resources download to have a free try from lead4pass, pass Cisco 300-135 exam test easily.

Latest Cisco 300-135 dumps pdf files free download: https://drive.google.com/open?id=0B_7qiYkH83VRS21DRS14UlZHNjg

Latest Cisco 300-206 dumps pdf files free download: https://drive.google.com/open?id=0B_7qiYkH83VRckk2V1ZwWXl5dVk

QUESTION 1
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
The fault condition is related to which technology?
A. Under the global configuration mode enter no access-list 10 command.
B. Under the global configuration mode enter no access-map vlan 10 command.
C. Under the global configuration mode enter no vlan access-map test1 10 command.
D. Under the global configuration mode enter no vlan filter test1 vlan-list 10 command.
Correct Answer: C

QUESTION 2
In computer networking a multicast address is an identifier for a group of hosts that have joined a multicast group. 300-135 pdf Multicast addressing can be used in the Link Layer (OSI Layer 2), such as Ethernet Multicast, as well as at the Internet Layer (OSI Layer 3) as IPv4 or IPv6 Multicast. Which two descriptions are correct regarding multicast addressing? ( choose two )
A. The first 23 bits of the multicast MAC address are 0x01-00-5E. This is a reserved value that indicates a multicast application.
B. The last 3 bytes (24 bits) of the multicast MAC address are 0x01-00-5E. This is a reserved value that indicates a multicast application.
C. To calculate the Layer 2 multicast address, the host maps the last 23 bits of the IP address into the last 24 bits of the MAC address. The high-order bit is set to 0.
D. The first 3 bytes (24 bits) of the multicast MAC address are 0x01-00-5E. This is a reserved value that indicates a multicast application.
Correct Answer: CD

QUESTION 3
You have been brought in to troubleshoot an EIGRP network. A network engineer has made configuration changes to the network rendering some locations unreachable. 300-135 dumps You are to locate the problem and suggest solution to resolve the issue.
300-135 dumps
R5 has become partially isolated from the remainder of the network. R5 can reach devices on directly connected networks but nothing else. What is causing the problem?
A. An outbound distribute list in R3
B. Inbound distribute lists in R5
C. An outbound distribute list in R6
D. Incorrect EIGRP routing process ID in R5
Correct Answer: B

QUESTION 4
The implementations group has been using the test bed to do a `proof-of-concept’. After several changes to the network addressing, routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2(2026::102:1).
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1F. DSW2
G. ASW1
H. ASW2
Correct Answer: B

QUESTION 5
Refer to the shown below.
%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
What statement is correct regarding the output shown in the graphic?
A. These two log messages will not have a severity level. They are not errors but are just informational messages.
B. The first log message is categorized as a warning message.
C. These messages regarding interface status are normal output and will always be displayed when you exit config mode.
D. The first log message is an error message with a severity level of 3.
E. The second message would be shown if the logging console warning command had been issued.
Correct Answer: D

QUESTION 6
What level of logging is enabled on a Router where the following logs are seen? 300-135 dumps
%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
A. alerts
B. critical
C. errors
D. notifications
Correct Answer: D

QUESTION 7
When troubleshooting an EIGRP connectivity problem, you notice that two connected EIGRP routers are not becoming EIGRP neighbors. 300-135 pdf A ping between the two routers was successful. What is the next thing that should be checked?
A. Verify that the EIGRP hello and hold timers match exactly.
B. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command.
C. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command.
D. Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.
Correct Answer: D

QUESTION 8
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?
A. Under the interface Serial0/0/0 configuration enter the ip nat inside command.
B. Under the interface Serial0/0/0 configuration enter the ip nat outside command.
C. Under the ip access-list standard nat_trafic configuration enter the permit 10.2.0.0 0.0.255.255 command.
D. Under the ip access-list standard nat_trafic configuration enter the permit 209.65.200.0 0.0.0.255 command.
Correct Answer: C

QUESTION 9
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the networkaddressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolate the cause of this fault and answer the following question.
The fault condition is related to which technology?
A. NTP
B. IP DHCP Server
C. Ipv4 OSPF Routing
D. Ipv4 EIGRP Routing.
E. Ipv4 Route Redistribution.
F. Ipv6 RIP Routing
G. Ipv6 OSPF Routing
H. Ipv4 and Ipv6 Interoperability
I. Ipv4 layer 3 security.
Correct Answer: B

QUESTION 10
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. 300-135 dumps After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?
A. Enable OSPF authentication on the s0/0/0 interface using the ip ospf authentication message-digest command
B. Enable OSPF routing on the s0/0/0 interface using the network 10.1.1.0 0.0.0.255 area 12 command.
C. Enable OSPF routing on the s0/0/0 interface using the network 209.65.200.0 0.0.0.255 area 12 command.
D. Redistribute the BGP route into OSPF using the redistribute BGP 65001 subnet command.
Correct Answer: A

Reference: https://www.lead4pass.com/300-135.html dumps pdf questions and answers free update.

Watch the video to learn more: